How many acoustic panels do I need for a wall?
Written by Matt W on 17th Nov 2026.
Each panel is 60cm wide.
Each panel is 240cm high.
Each panel covers about 1.44m2.
Products and prices checked 17 November 2026.
Divide your wall section width in centimetres by 60, then round up to find the number of panels needed. Monster acoustic slat panels are 240cm high and 60cm wide. A 180cm section needs three panels. A 300cm section needs five. Each panel covers about 1.44m2 before cuts. Ceilings below 240cm require length trimming, so check height before you choose packs.
Key takeaways
- Calculate panels by width: divide centimetres by 60 and round up.
- Each panel measures 240cm high x 60cm wide x 2.1cm deep.
- Two panels make a 1.2m run, with the slat pattern continuing across the join.
- Six panels cover about 8.64m2 before cuts.
- Felt absorbs some reflected sound, but these panels do not soundproof walls.
Buyer's note from Matt W: I start with the width of the section you want to cover. I then check height and any sockets before comparing packs. I compare the price per panel, because the smallest order is not always the cheapest per panel. For shorter walls, I check the required cuts before suggesting quantities.
- Matt W, Acoustic Panel Stores
How many acoustic panels do I need?
You need your wall section width divided by 60cm, rounded up to the next whole panel.
This method applies to upright Monster panels across one section up to 240cm high. Use the width you actually want covered, rather than automatically measuring the entire room.
The calculation gives a purchase quantity, including a final panel that may need width trimming. Rounding down leaves part of your chosen section uncovered.
Panel area is a useful second check. Each panel covers about 1.44m2, so six panels cover about 8.64m2 before trimming. Width remains the clearer starting point for a continuous upright run.
How do you measure a wall for slat panels?
Measure the full section width and height, then record sockets, skirting and corners before planning cuts.
Start by deciding where the panel run begins and ends. Record that width in centimetres for the panel calculation. Record height separately, with the skirting position clearly marked.
For acoustic panel sizes, use the complete dimensions: 240cm high x 60cm wide x 2.1cm deep. Width determines the count across the wall. Height determines whether the panel length needs trimming.
Mark each socket's position within the whole run. Check corners and the intended panel edges before deciding where individual cuts belong. The listing specifically advises measuring the whole run before trimming around sockets, corners or skirting.
A fixing kit is included for mounting directly to a suitable wall or ceiling. Check the surface and fixing method before starting. Each panel weighs about 11kg, so suitability matters alongside the visible layout.
Watch out: measure the whole run. Include sockets, corners and skirting before trimming any panel. Plan their positions across the complete section. A panel count alone does not identify where cuts belong.
How many panels fit common wall widths?
A 120cm section needs two panels, while a 420cm section needs seven.
The table gives the simplest pack combinations for common widths. Each count assumes upright panels, with height checked separately. These widths divide exactly into 60cm panels.
| Section width | Panels needed | Simplest packs |
|---|---|---|
| 120cm | 2 | One 2-pack |
| 180cm | 3 | One 3-pack |
| 240cm | 4 | Two 2-packs |
| 300cm | 5 | One 3-pack plus one 2-pack |
| 360cm | 6 | Two 3-packs |
| 420cm | 7 | One 3-pack plus two 2-packs |
Two panels side by side make a 1.2m run, with the slat rhythm continuing across the join. A 3-pack has a laid width of 180cm and covers about 4.32m2 before cuts.
Matt's pick: Monster 3-Pack - Light Walnut
Best for: A 180cm-wide section in one order.
Why we rate it: Three panels cover about 4.32m2 before cuts. At prices checked on 17 November 2026, this pack has the lowest per-panel cost in the range.
Price: £223
Should you buy single panels, 2-packs or 3-packs?
At prices checked on 17 November 2026, packs cost less per panel than singles in Anthracite Grey and Light Walnut.
Compare each pack price divided by its panel count. Then compare the total order needed for your measured width.
Anthracite Grey has a smaller per-panel gap between its 2-pack and 3-pack than Light Walnut. Both finishes have their lowest per-panel cost in the 3-pack, at the checked prices.
The Light Walnut options below show the relationship between quantity, laid width and product price.
| Light Walnut option | Panels | Laid width | Price |
|---|---|---|---|
| Single panel | 1 | 60cm | £103 |
| 2-pack | 2 | 120cm | £155 |
| 3-pack, Matt's pick | 3 | 180cm | £223 |
Anthracite Grey and Light Walnut are available as singles, 2-packs and 3-packs. Oak and Dark Walnut are available as 2-packs. Compare grey panels or walnut panels after checking your required quantity.
What if your ceiling is lower than 240cm?
A ceiling below 240cm means the panel length needs trimming.
Shortening an upright panel does not change its listed 60cm width. Your width calculation therefore remains the starting point for the panel count.
Check the intended top and bottom positions, including skirting, before marking the required length. Measure the whole run before cutting individual panels.
The panels have MDF slats with a wood-effect veneer and 9mm flame-retardant sound-absorbing felt backing. The listing gives a "27mm MDF slat" and 13mm gaps. Those gaps expose the felt and keep the pattern even.
How much of the wall should you cover?
The listings give no fixed coverage rule; more absorbing area generally means a bigger effect.
Start with an area where sound first reflects, such as behind a desk or beside a TV. A large bare wall is another sensible starting point.
Hard surfaces such as plaster, glass and bare floors reflect sound. Those reflections build up as echo and reverberation. Soft, porous felt absorbs part of the sound that reaches it, so less sound reflects back.
Acoustic panels make a room sound calmer and speech clearer inside that room. They do not soundproof it. Stopping sound passing to neighbours needs heavy, airtight construction, which wall panels do not provide.
No absorption rating, NRC or decibel figure is stated for this range. Panel dimensions establish coverage, but they do not establish a measured sound reduction.
"I can match different wall widths with this range's single panels and packs. I can also compare Anthracite Grey and Light Walnut across all three pack sizes."
- Matt W, Acoustic Panel Stores
Frequently asked questions
What size are Monster acoustic slat panels?
Each panel is 240cm high x 60cm wide x 2.1cm deep. It covers about 1.44m2 before cuts and weighs about 11kg.
How many panels do I need for a 300cm wall?
A 300cm-wide section needs five panels. One 3-pack plus one 2-pack supplies that quantity. Check the height separately before ordering.
Can I trim panels for a lower ceiling?
Panels need length trimming when the ceiling is below 240cm. Measure the whole run, including sockets, corners and skirting, before trimming.
Do these acoustic panels soundproof a room?
No, these panels absorb some reflected sound but do not soundproof a room. Stopping sound passing through walls or floors needs heavy, airtight construction.
Is a fixing kit included?
A fixing kit is included for a suitable wall or ceiling. Check the surface and fixing method before starting.
What delivery and warranty details are stated?
Delivery is free within 3-5 working days; no warranty term is stated. Check the product listing before ordering.
Related articles
Sources checked
- Acoustic Panel Stores product listings for Monster acoustic slat wall panels, checked 17 November 2026.
- Panel counts calculated from listed panel widths.